DJI Naza-M V2 Multirotor Gyro System w/ GPS

DJISKU: DJI-Acc-Naza-M-V2

Price:
Sale priceUSD $199

Description

Feel the Industrial Grade Stability - turn your hobby drone into a working equipment!
NAZA is a lightweight multi-axis control platform specially designed for aeromodel hobbyists. It is a small all-in-one module. It has D-Bus support, upgrade support, and extendible port.




Take your drone to another level!
You will not believe your drone could be this stable.


With some RC experience, you should be able to install it
The system itself it easy, but setting up Transmitter is tricky, please prepare your transmitter manual for the job.



The LED module
Put the LED module at the rear of the drone so you can see clearly for the status of the drone, like GPS signal reception, battery voltage.... etc.




GPS for perfect positioning, it will be hovering still at the same spot
The plug and play GPS module will greatly enhance the performance for Aerial Photography with accurate Position Hold, Return-To-Home and Intelligent Orientation Control functionalities. With the GPS Module, the multi-rotor will have position and altitude locked accurately even in windy conditions. Hovering accuracy is approximately 2.5m horizontal and 0.8m vertical.

Watch out for the GPS Module Direction, it matters
Remember, red arrow Forward!!!

Course Lock and Home Lock
Usually, the forward direction of a flying multi-rotor is the same as the nose direction. By using Intelligent Orientation Control (IOC), wherever the nose points, the forward direction has nothing to do with nose direction: In course lock flying, the forward direction is the same as a recorded nose direction.

Lost transmitter signal? Don't worry, it will Auto Return Home
If your transmitter supports failsafe, then you can set failsafe through port-U. Naza controller has built-in auto level failsafe function, which means when the communication between MC and the transmitter is disconnected, the outputs of all command sticks from controller will go to center position. 

Four ways to "Arm" the drone
Sometimes we may accidentally moved the throttle stick and cause disaster, so you must do some gestures to start the motors, this is a safety feature.

Online firmware update
Easy firmware upgrade, extendible port for future use is available.

Support Futaba S.Bus
With Futaba S.Bus, you can use only one cable to replace a bunch of cable, connecting between a Futaba Receiver and the Naza-M Gyro, clean and tidy.

Naza-M supports Nine types of multi rotors
Naza-M V2 now supports nine types of multi-rotor, which meets the different needs of the enthusiasts.
Quad I, Quad X; Hexa I, Hexa V, Hexa Y, Hexa IY; Octo X, Octo I, Octo V; ( Naza-M V2 does not support the aircraft which has large vibration, so when you choose to use hexa-rotor or octo-rotor, please use the vibration dampening devices accordingly.







Naza-M V2 Multi rotor Gyro System Specifications :
Supported Multi-rotor : Quad-rotor I4, X4, Hex-rotor I6, X6, IY6, Y6, Octo-rotor I8,V8,X8
Supported ESC output : 400Hz refresh frequency
Recommended Transmitter : PCM or 2.4GHz with minimum 4 channels
Working Voltage Range : MC:4.8V~5.5V; VU Input: 7.4V ~ 26.0 V (recommend 2S ~ 6S LiPo)
Output(V-SEN port red wire): 3A@5V (burst current:7.5A)
Power Consumption : MAX: 3.15W(0.25A@12.6V); Normal:1.638W(0.13A@12.6V)
Operating Temperature : -10°C ~ 50°C
Assistant Software System Requirement : Windows XP sp3 / Windows 7 / Windows 8
Max Yaw Angular Velocity : 200°/s
Max Tilt Angle : 35°
Ascent / Descent : 6m/s and 4.5m/s
Weight : MC:27g; PMU:28g; GPS:27g; LED:13g
Dimensions MC: 45.5mm x 32.5mm x 18.5mm
Dimensions PMU: 39.5mm x 27.5mm x 10.0mm
Dimensions GPS & Compass 46mm(diameter)x10mm
Dimensions LED: 25mm x 25mm x 7.0mm
Dimensions VU : 32.2mm x 21.1mm x 7.7mm
Built-In Functions : Multiple Autopilot Control Mode
Enhanced Fail-safe
Low Voltage Protection
S-Bus Receiver Support
PPM Receiver Support
Independent PMU Module
2-axle Gimbal Support
This package includes :
1. Naza-M V2 Flight Controller
2. LED Module
3. PMU Module
4. GPS Compass Module
5. LED Module
6. 2 X 3M VHB Foam Tape
7. 8 X Servo Cable
8. 1 X USB Cable

* Manual is NOT included, because DJI always update manual, please click here to download the latest manual


 

Payment & Security

PayPal

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

Estimate shipping

You may also like

Recently viewed