Feel the Industrial Grade Stability - turn your hobby drone into a working equipment!
NAZA is a lightweight multi-axis control platform specially designed for aeromodel hobbyists. It is a small all-in-one module. It has D-Bus support, upgrade support, and extendible port.
Different from WooKong-M for heavy payloads and aero photography, NAZA not only inherits the outstanding flight stability of DJI products, but also provides excellent maneuverability, which gives hobbyists wonderful flight experience.
Difference between NAZA-M Lite, NAZA-M V1 and NAZA-M V2?
NAZA-M V1 is discontinued in Mid 2013 and replaced with NAZA-M V2, they put some extendability on the NAZA-M V2 and price went up, to fill the entry level gap they launched the NAZA-M Lite, basically the same with NAZA-M V1, but CANNOT extend with fancy gadgets like PMU (Power Management Unit / BEC), Zenmuse Camera Gimbal, iOSD On Screen Display unit or Ground Station Data Link. However, price for the NAZA-M Lite is really good and it gives same stability and GPS Auto Hovering as the NAZA-M V2, so we think if you don't plan to play those fancy functions, stick with the NAZA-M Lite, if you plan to plug those gadgets in the future, go with the NAZA-M V2.
Take your drone to another level!
You will not believe your drone could be this stable.
With some RC experience, you should be able to install it
The system itself it easy, but setting up Transmitter is tricky, please prepare your transmitter manual for the job.
All in one design
DJI adheres to continuous innovation and improvement. With the new firmware, new attitude stabilization algorithm and optimized hardware structure, the Naza-M V2 provides better flight performance. The innovative All-in-one design simplifies installation and saves space and weight. It contains inner damping, controllers, 3-axis gyroscope, 3-axis accelerometer and barometer in its light and small Main Controller. It can measure flying altitude and attitude and therefore can be used for autopilot/automatic control.
Different from V1, the V-SEN unit became this PMU
The Naza PMU V2 has enhanced BEC functionality and provides extendable CAN BUS ports, which can support iOSD, Zenmuse H3-2D gimbal (pitch control). Support is also included for optional Bluetooth LED module to allow parameter adjustment via a mobile APP (future firmware upgrade required for this functionality)
The LED module
Put the LED module at the rear of the drone so you can see clearly for the status of the drone, like GPS signal reception, battery voltage.... etc.
Advanced Altitude Stabilizing Algorithm
||What it means
||Drone is gathering start up data (adjusting temperature sensor), this takes about 1-2 minutes, please be patient, during this process DO NOT touch me. Once gathered all data, the three yellow will gone.
||GPS Mode, found less than 5 satellites, do not fly in this status!
(Green - Red Red Red)
||GPS Mode, found only 5 satellites, do not fly in this status!
(Green - Red Red)
||GPS Mode, found only 6 satellites, do not fly in this status!
(Green - Red)
||GPS Mode, all 7 satellites have been found, this is the best condition, you can fly now.
(Green - Green - Green and keep looping)
||Altitude Mode, found less than 5 satellites, you can still fly, just do not switch to GPS mode when flying.
(Yellow - Red Red Red)
||Altitude Mode, found 5 satellites, you can still fly, just do not switch to GPS mode when flying.
(Yellow - Red Red)
||Altitude Mode, found 6 satellites, you can still fly, just do not switch to GPS mode when flying.
(Yellow - Red)
||Altitude Mode, found all 7 satellites, you can switch between GPS mode and ATTI mode as you like.
(Yellow - Yellow - Yellow and keep looping)
||Working in IOC mode (Course Lock), no matter what's the direction the drone is pointing at, you control it just like standing behind the drone, you pull back elevator stick, it will come back to home point.
(Yellow Green -Yellow Green - Yellow Green and keep looping)
||Recording home point. When it found 6 or more satellites for more than 8 seconds AND you moved throttle stick for the first time, it will record this point as home point, it will fly back to this point if you switch off transmitter. Make sure this home point location is cleared all the time.
(Suddenly Fast Flashing Green for 7-8 times)
||Naza Gyro lost Transmitter signal, this will happen when you switch off transmitter. With good GPS signal, it will go up to 20 meters high and fly back to the home point, hover for 15 seconds and slowly descend to the ground.
(Fast Flashing Yellow and keep on flashing)
||Low battery, no good, come back asap!
(Fast Flashing Red and keep on flashing)
The latest fourth generation attitude stabilization algorithm not only inherits the outstanding flight stability of DJI products, but also provides excellent maneuverability even without the GPS module. It is more flexible and stable, and gives the hobbyists a wonderful flight experience. New features have been included such as GPS course automatic compensation, GPS & Compass sensor calibration, new take-off mode and so on.
Switching Modes - GPS, Altitude or Manual
It offers three types of control modes: GPS Atti. Mode (with GPS module), Atti. Mode, Manual Mode. The pilot can switch between the three modes to achieve different flight characteristics. It also can adjust automatically within the flight environment and intelligently switch between GPS Atti. Mode and Atti. Mode to make sure the flight is safe and secure. In the software at the position of the manual mode you can choose manual, attitude or failsafe; it supports one key failsafe trigger.
GPS for perfect positioning, it will be hovering still at the same spot
The plug and play GPS module will greatly enhance the performance for Aerial Photography with accurate Position Hold, Return-To-Home and Intelligent Orientation Control functionalities. With the GPS Module, the multi-rotor will have position and altitude locked accurately even in windy conditions. Hovering accuracy is approximately 2.5m horizontal and 0.8m vertical.
Watch out for the GPS Module Direction, it matters
Remember, red arrow Forward!!!
Course Lock and Home Lock
Usually, the forward direction of a flying multi-rotor is the same as the nose direction. By using Intelligent Orientation Control (IOC), wherever the nose points, the forward direction has nothing to do with nose direction:
In course lock flying, the forward direction is the same as a recorded nose direction.
Lost transmitter signal? Don't worry, it will Auto Return Home
If your transmitter supports failsafe, then you can set failsafe through port-U. Naza controller has built-in auto level failsafe function, which means when the communication between MC and the transmitter is disconnected, the outputs of all command sticks from controller will go to center position. If the GPS module is used, you can also set RTH on failsafe. If your transmitter has only 4 channels, then MC will work in Atti. Mode by default without the failsafe function.
Two levels of battery voltage warning
In order to prevent your multi-rotor from crashing or other harmful consequences caused by low battery voltage, we have designed two levels of low voltage protection. You can choose not to use this, however we strongly recommend you to enable the protection. Both levels of protection have LED warning as default. The first level will blink the red light continuously; the second level will blink red light continuously and the multi-rotor will descend and land. In manual mode when low voltage protection is triggered the LED warning will be active only.
Four ways to "Arm" the drone
Sometimes we may accidentally moved the throttle stick and cause disaster, so you must do some gestures to start the motors, this is a safety feature.
Online firmware update
Easy firmware upgrade, extendible port for future use is available.
Support Futaba S.Bus
With Futaba S.Bus, you can use only one cable to replace a bunch of cable, connecting between a Futaba Receiver and the Naza-M Gyro, clean and tidy.
Naza-M supports Nine types of multi rotors
Naza-M V2 now supports nine types of multi-rotor, which meets the different needs of the enthusiasts.
Quad I, Quad X;
Hexa I, Hexa V, Hexa Y, Hexa IY;
Octo X, Octo I, Octo V; ( Naza-M V2 does not support the aircraft which has large vibration, so when you choose to use hexa-rotor or octo-rotor, please use the vibration dampening devices accordingly.
Stabilizing a camera gimbal
The gimbal stabilization module is compatible with almost all 2-axis gimbal systems. The system will adjust the gimbal and camera according to the attitude of the helicopter after setting the parameters the first time.
We put it on the Storm Drone and upgraded to Carbon Fiber rotors, that's fun!
The Naza-M with GPS system will replace the original FF Gyro Board, you need to remove that first.
Tips and Tricks - Balance your Drone rotors first!
Easy to do yet very important, this will eliminate all micro vibration and get smooth and professional video footage.
Naza-M V2 Multi rotor Gyro System Specifications :
Supported Multi-rotor : Quad-rotor I4, X4,
Hex-rotor I6, X6, IY6, Y6,
Supported ESC output : 400Hz refresh frequency
Recommended Transmitter : PCM or 2.4GHz with minimum 4 channels
Working Voltage Range : MC:4.8V~5.5V;
VU Input: 7.4V ~ 26.0 V (recommend 2S ~ 6S LiPo)
Output(V-SEN port red wire): 3A@5V
Power Consumption : MAX: 3.15W(0.25A@12.6V);
Operating Temperature : -10°C ~ 50°C
Assistant Software System Requirement : Windows XP sp3 / Windows 7 / Windows 8
Max Yaw Angular Velocity : 200°/s
Max Tilt Angle : 35°
Ascent / Descent : 6m/s and 4.5m/s
Weight : MC:27g;
Dimensions MC: 45.5mm x 32.5mm x 18.5mm
Dimensions PMU: 39.5mm x 27.5mm x 10.0mm
Dimensions GPS & Compass 46mm(diameter)x10mm
Dimensions LED: 25mm x 25mm x 7.0mm
Dimensions VU : 32.2mm x 21.1mm x 7.7mm
Built-In Functions : Multiple Autopilot Control Mode
Low Voltage Protection
S-Bus Receiver Support
PPM Receiver Support
Independent PMU Module
2-axle Gimbal Support
This package includes :
Naza-M V2 Flight Controller
GPS Compass Module
2 X 3M VHB Foam Tape
8 X Servo Cable
1 X USB Cable
Manual is NOT
included, because DJI always update manual, please click here
to download the latest manual
Suitable for :
The Naza-M V2 Gyro is not hard to put on any drone, including the Storm Drone (must remove the old FF Gyro first), simply follow the Naza-M manual downloaded from their website and you should be able to connect the cables correctly, however, the difficult part is setting up the transmitter, you need to know how to work with your transmitter like assigning functions on the 3 way switch, for that we may not able to help because every Transmitter is different.
Product Status : In-Stock
Get it now for
USD $599.00 USD $159.00 only!
|iPad Ground Station: